AEROENGINES

AEROENGINES

_
iten
Code
56852
ACADEMIC YEAR
2018/2019
CREDITS
6 credits during the 2nd year of 9270 Mechanical Engineering - Energy and Aeronautics (LM-33) GENOVA
SCIENTIFIC DISCIPLINARY SECTOR
ING-IND/08
LANGUAGE
Italian
TEACHING LOCATION
GENOVA (Mechanical Engineering - Energy and Aeronautics)
semester
2° Semester
Teaching materials

OVERVIEW

The course provides to the students the basic rules for the preliminary design of the different aero-engine components, in order to satisfy the required thrust, and the thermodynamic constrains imposed by the cycle analysis. In a second phase the operation of each component will be deeply investigated looking at the internal aerodynamics, thus highlighting the most important flow and geometrical parameters affecting the component performance.

AIMS AND CONTENT

LEARNING OUTCOMES

The main objectives of the course are focused on the design of the different components characterizing an aircraft engine: engine inlet, compressor, combustor chamber, turbine, diffusers and nozzle.

AIMS AND LEARNING OUTCOMES

At the end of the course the student should be able to:

- perform an accurate cycle analysis of the aeroengine, identifying the boundary conditions for the design of the different components;

 - design, through a preliminary procedure, each aeroengine component: intake, compressor, combustion chamber, turbine and propulsive nozzle;

- analyze in detail the aerodynamics of each component;

- apply the matching of the components in order to identify the nominal operating point of the system.

Teaching methods

Frontal lessons will be mainly employed in the course. The basic design rules of each component will be provided. Experimental and numerical results characterizing the real operation of each component will be also shown. It is strongly suggested the participation of the student to the lessons, since the examination is driven by arguments discussed and presented during the lessons 

SYLLABUS/CONTENT

  • Performance of the engine. Analysis of the thermodynamic cycle of a turbojet engine. Pressure and temperature ratios of the cycle. Thrust and specific fuel consumption
  • Layout of a turbojet engine. Definition of the main design parameters of the different engine  components.
  • Engine inlet, compressor rig, combustor chamber, turbine, diffusers and nozzle, post-combustor. Analysis of the thrust characterizing the different components.
  • Dimensioning and design criteria of the engine components:
  1. Reduced mass flow for the dimensioning of the engine inlet. Diffuser performance chart from Sovran and Klomp. Effect of flow non uniformity on the pressure recovery and total pressure losses.
  2. Design of the exit nozzle. Loss of thrust due blockage mass flow (discharge coefficient) and total pressure losses (due to boundary layer evolution). Comparison between converging and converging-diverging nozzles.
  3.  Mean line design of compressors and turbines stages. Identification of the stage number. Radial equilibrium equation for the dimensioning of both compressor and turbine stages. Lieblein and Zweifel correlations for limitation of the aerodynamic loading of compressor and turbine blades, respectively. Design of compressor blades with NACA65 profiles. Design of parabolic-arc turbine profiles. Introduction to secondary flows evolution and their effects on total pressure and exit flow angle. Correlations.
  4. Design of S-shaped duct. Effects of curvature radii and inlet flow unsteadiness.
  • Kerrebrock and Lefebvre correlations for the determination of the total pressure losses within the combustor chamber.
  • Matching of the different engine components. Off-design functioning of the engine. 

RECOMMENDED READING/BIBLIOGRAPHY

  • S. Farokhi, “Aircraft Propulsion”, Wiley and Sons, 2009
  • J. Mattingly, W. Heiser, D. Pratt, “Aircraft Engine Design: Second Edition”, AIAA Education Series 2002

TEACHERS AND EXAM BOARD

Exam Board

DANIELE SIMONI (President)

PIETRO ZUNINO

MARINA UBALDI

DAVIDE LENGANI

FRANCESCA SATTA

LESSONS

Teaching methods

Frontal lessons will be mainly employed in the course. The basic design rules of each component will be provided. Experimental and numerical results characterizing the real operation of each component will be also shown. It is strongly suggested the participation of the student to the lessons, since the examination is driven by arguments discussed and presented during the lessons 

ORARI

L'orario di tutti gli insegnamenti è consultabile su EasyAcademy.

Vedi anche:

AEROENGINES

EXAMS

Exam description

The examination will be carried out by means of an oral discussion. The examination data will be provided previous appointment.

Assessment methods

The oral examination will allow to verify the acquired knowledge of the student regarding the operation of the different components, and how they can be optimized thanks to an increasing knowledge of the internal aerodynamics of the components, as well as in the evaluation of the capability of the student in adopting the design rules and the matching between the different components.